Passing wire down through Exterior Wall
Replacing some old wiring with crumbling insulation. One of the wires passes down through an exterior wall from the attic, to an outlet on the second floor, and continues down to the first floor.
I attempted to follow the same path, but I drilled over 6 inches into the bottom of the wall and still haven't broken through.
The drill seems to be really struggling through the wood. Started with a 3/4 auger bit on an 18" extension. That stopped making any more progress so I switched to a 5/8" spade bit on the extension instead. Now the spade bit is fully into the hole along with part of the extension.
Not sure if I should keep going. The old wire goes through, but is there a chance I'm going to cause problems if I keep drilling? The house was built in 1930, so I assume the drilling difficulty is due to the wood used. I'm just worried about weakening the beam or something.
wiring old-house
asked 5 hours ago
TypeKG
564
add a comment |
Replacing some old wiring with crumbling insulation. One of the wires passes down through an exterior wall from the attic, to an outlet on the second floor, and continues down to the first floor.
I attempted to follow the same path, but I drilled over 6 inches into the bottom of the wall and still haven't broken through.
The drill seems to be really struggling through the wood. Started with a 3/4 auger bit on an 18" extension. That stopped making any more progress so I switched to a 5/8" spade bit on the extension instead. Now the spade bit is fully into the hole along with part of the extension.
Not sure if I should keep going. The old wire goes through, but is there a chance I'm going to cause problems if I keep drilling? The house was built in 1930, so I assume the drilling difficulty is due to the wood used. I'm just worried about weakening the beam or something.
wiring old-house
asked 5 hours ago
TypeKG
564
Pictures might help us understand what you are dealing with..
– IronEagle
4 hours ago
You are drilling directly into a stud perhaps? Although drilling through bottom plate flooring lower level top plate and wall framing is going to be at least 6 inches
– Kris
4 hours ago
Since it's on the exterior wall, you could be going into the wood that goes along the outside wall between floors around the whole house(I forget what it's called). Try drilling the same distance from the drywall as the original hole.
– HazardousGlitch
4 hours ago
1
Either what Kris said (try another hole a good distance away), or you could just be dealing with platform framing, a method fairly common in the 1930's. There could easily be a giant beam running between the floors on the exterior walls. Is it possible to remove the old wiring and see how thick the hole is that it goes through?
– IronEagle
4 hours ago
add a comment |
Replacing some old wiring with crumbling insulation. One of the wires passes down through an exterior wall from the attic, to an outlet on the second floor, and continues down to the first floor.
I attempted to follow the same path, but I drilled over 6 inches into the bottom of the wall and still haven't broken through.
The drill seems to be really struggling through the wood. Started with a 3/4 auger bit on an 18" extension. That stopped making any more progress so I switched to a 5/8" spade bit on the extension instead. Now the spade bit is fully into the hole along with part of the extension.
Not sure if I should keep going. The old wire goes through, but is there a chance I'm going to cause problems if I keep drilling? The house was built in 1930, so I assume the drilling difficulty is due to the wood used. I'm just worried about weakening the beam or something.
wiring old-house
asked 5 hours ago
TypeKG
564
Replacing some old wiring with crumbling insulation. One of the wires passes down through an exterior wall from the attic, to an outlet on the second floor, and continues down to the first floor.
I attempted to follow the same path, but I drilled over 6 inches into the bottom of the wall and still haven't broken through.
The drill seems to be really struggling through the wood. Started with a 3/4 auger bit on an 18" extension. That stopped making any more progress so I switched to a 5/8" spade bit on the extension instead. Now the spade bit is fully into the hole along with part of the extension.
Not sure if I should keep going. The old wire goes through, but is there a chance I'm going to cause problems if I keep drilling? The house was built in 1930, so I assume the drilling difficulty is due to the wood used. I'm just worried about weakening the beam or something.
wiring old-house
wiring old-house
asked 5 hours ago
TypeKG
564
asked 5 hours ago
TypeKG
564
edited 4 hours ago
asked 5 hours ago
TypeKG
564
asked 5 hours ago
TypeKG
564
asked 5 hours ago
TypeKG
564
564
Pictures might help us understand what you are dealing with..
– IronEagle
4 hours ago
You are drilling directly into a stud perhaps? Although drilling through bottom plate flooring lower level top plate and wall framing is going to be at least 6 inches
– Kris
4 hours ago
Since it's on the exterior wall, you could be going into the wood that goes along the outside wall between floors around the whole house(I forget what it's called). Try drilling the same distance from the drywall as the original hole.
– HazardousGlitch
4 hours ago
1
Either what Kris said (try another hole a good distance away), or you could just be dealing with platform framing, a method fairly common in the 1930's. There could easily be a giant beam running between the floors on the exterior walls. Is it possible to remove the old wiring and see how thick the hole is that it goes through?
– IronEagle
4 hours ago
add a comment |
Pictures might help us understand what you are dealing with..
– IronEagle
4 hours ago
You are drilling directly into a stud perhaps? Although drilling through bottom plate flooring lower level top plate and wall framing is going to be at least 6 inches
– Kris
4 hours ago
Since it's on the exterior wall, you could be going into the wood that goes along the outside wall between floors around the whole house(I forget what it's called). Try drilling the same distance from the drywall as the original hole.
– HazardousGlitch
4 hours ago
1
Either what Kris said (try another hole a good distance away), or you could just be dealing with platform framing, a method fairly common in the 1930's. There could easily be a giant beam running between the floors on the exterior walls. Is it possible to remove the old wiring and see how thick the hole is that it goes through?
– IronEagle
4 hours ago
Pictures might help us understand what you are dealing with..
– IronEagle
4 hours ago
Pictures might help us understand what you are dealing with..
– IronEagle
4 hours ago
You are drilling directly into a stud perhaps? Although drilling through bottom plate flooring lower level top plate and wall framing is going to be at least 6 inches
– Kris
4 hours ago
You are drilling directly into a stud perhaps? Although drilling through bottom plate flooring lower level top plate and wall framing is going to be at least 6 inches
– Kris
4 hours ago
Since it's on the exterior wall, you could be going into the wood that goes along the outside wall between floors around the whole house(I forget what it's called). Try drilling the same distance from the drywall as the original hole.
– HazardousGlitch
4 hours ago
Since it's on the exterior wall, you could be going into the wood that goes along the outside wall between floors around the whole house(I forget what it's called). Try drilling the same distance from the drywall as the original hole.
– HazardousGlitch
4 hours ago
1
1
Either what Kris said (try another hole a good distance away), or you could just be dealing with platform framing, a method fairly common in the 1930's. There could easily be a giant beam running between the floors on the exterior walls. Is it possible to remove the old wiring and see how thick the hole is that it goes through?
– IronEagle
4 hours ago
Either what Kris said (try another hole a good distance away), or you could just be dealing with platform framing, a method fairly common in the 1930's. There could easily be a giant beam running between the floors on the exterior walls. Is it possible to remove the old wiring and see how thick the hole is that it goes through?
– IronEagle
4 hours ago
add a comment |
1 Answer
1
active
oldest
votes
HazardousGlitch had a good suggestion. I don't think I was drilling into to top of a stud because I had tried several holes before posting.
Opened up the wall more so I could position the drill closer to the drywall and went through easily. Above I posted the wrong photo that didn't have the deep hole. Now you can see the deep hole (left bottom) and the successful hole (right by the old wire). You can also see my other failed attempts.
Thanks for the help!
answered 3 hours ago
TypeKG
564
Good to hear! Be sure to mark this as the answer.
– HazardousGlitch
3 hours ago
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "73"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f153658%2fpassing-wire-down-through-exterior-wall%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
HazardousGlitch had a good suggestion. I don't think I was drilling into to top of a stud because I had tried several holes before posting.
Opened up the wall more so I could position the drill closer to the drywall and went through easily. Above I posted the wrong photo that didn't have the deep hole. Now you can see the deep hole (left bottom) and the successful hole (right by the old wire). You can also see my other failed attempts.
Thanks for the help!
answered 3 hours ago
TypeKG
564
Good to hear! Be sure to mark this as the answer.
– HazardousGlitch
3 hours ago
add a comment |
HazardousGlitch had a good suggestion. I don't think I was drilling into to top of a stud because I had tried several holes before posting.
Opened up the wall more so I could position the drill closer to the drywall and went through easily. Above I posted the wrong photo that didn't have the deep hole. Now you can see the deep hole (left bottom) and the successful hole (right by the old wire). You can also see my other failed attempts.
Thanks for the help!
answered 3 hours ago
TypeKG
564
Good to hear! Be sure to mark this as the answer.
– HazardousGlitch
3 hours ago
add a comment |
HazardousGlitch had a good suggestion. I don't think I was drilling into to top of a stud because I had tried several holes before posting.
Opened up the wall more so I could position the drill closer to the drywall and went through easily. Above I posted the wrong photo that didn't have the deep hole. Now you can see the deep hole (left bottom) and the successful hole (right by the old wire). You can also see my other failed attempts.
Thanks for the help!
answered 3 hours ago
TypeKG
564
HazardousGlitch had a good suggestion. I don't think I was drilling into to top of a stud because I had tried several holes before posting.
Opened up the wall more so I could position the drill closer to the drywall and went through easily. Above I posted the wrong photo that didn't have the deep hole. Now you can see the deep hole (left bottom) and the successful hole (right by the old wire). You can also see my other failed attempts.
Thanks for the help!
answered 3 hours ago
TypeKG
564
answered 3 hours ago
TypeKG
564
answered 3 hours ago
TypeKG
564
answered 3 hours ago
TypeKG
564
564
Good to hear! Be sure to mark this as the answer.
– HazardousGlitch
3 hours ago
add a comment |
Good to hear! Be sure to mark this as the answer.
– HazardousGlitch
3 hours ago
Good to hear! Be sure to mark this as the answer.
– HazardousGlitch
3 hours ago
Good to hear! Be sure to mark this as the answer.
– HazardousGlitch
3 hours ago
add a comment |
Thanks for contributing an answer to Home Improvement Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f153658%2fpassing-wire-down-through-exterior-wall%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Pictures might help us understand what you are dealing with..
– IronEagle
4 hours ago
You are drilling directly into a stud perhaps? Although drilling through bottom plate flooring lower level top plate and wall framing is going to be at least 6 inches
– Kris
4 hours ago
Since it's on the exterior wall, you could be going into the wood that goes along the outside wall between floors around the whole house(I forget what it's called). Try drilling the same distance from the drywall as the original hole.
– HazardousGlitch
4 hours ago
1
Either what Kris said (try another hole a good distance away), or you could just be dealing with platform framing, a method fairly common in the 1930's. There could easily be a giant beam running between the floors on the exterior walls. Is it possible to remove the old wiring and see how thick the hole is that it goes through?
– IronEagle
4 hours ago