ssh for “No route to host” but ping works
up vote
-1
down vote
favorite
Hope ssh access host2 via host1, but ssh return "No route to host", but ping works and iptables return inactive.
[host1 ~] ping 10.158.131.165
PING 10.158.131.165 (10.158.131.165) 56(84) bytes of data.
64 bytes from 10.158.131.165: icmp_seq=1 ttl=58 time=1.69 ms
64 bytes from 10.158.131.165: icmp_seq=2 ttl=58 time=1.68 ms
^C
--- 10.158.131.165 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 1001ms
rtt min/avg/max/mdev = 1.684/1.687/1.690/0.003 ms
[host1 ~] telnet 10.158.131.165 22
Trying 10.158.131.165...
telnet: connect to address 10.158.131.165: No route to host
[host1 ~] ssh ssdrive@10.158.131.165
ssh: connect to host 10.158.131.165 port 22: No route to host
Host1:
[host1 ~] ifconfig
eno1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.166.62.130 netmask 255.255.240.0 broadcast 10.166.63.255
inet6 fe80::f64d:30ff:fe66:a895 prefixlen 64 scopeid 0x20<link>
ether f4:4d:30:66:a8:95 txqueuelen 1000 (Ethernet)
RX packets 3313964 bytes 529261130 (504.7 MiB)
RX errors 0 dropped 233 overruns 0 frame 0
TX packets 1258374 bytes 492612963 (469.7 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 16 memory 0xdf200000-df220000
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 8 bytes 528 (528.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 8 bytes 528 (528.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
[host1 ~] route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 10.166.56.1 0.0.0.0 UG 0 0 0 eno1
10.166.48.0 0.0.0.0 255.255.240.0 U 0 0 0 eno1
169.254.0.0 0.0.0.0 255.255.0.0 U 1002 0 0 eno1
# service iptables status
Redirecting to /bin/systemctl status iptables.service
iptables.service - IPv4 firewall with iptables
Loaded: loaded (/usr/lib/systemd/system/iptables.service; enabled; vendor preset: disabled)
Active: inactive (dead)
Host2:
[host2 ~]$ ifconfig
enp3s0f1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.158.131.165 netmask 255.255.240.0 broadcast 10.158.143.255
inet6 fe80::ec4:7aff:fe22:badf prefixlen 64 scopeid 0x20<link>
ether 0c:c4:7a:22:ba:df txqueuelen 1000 (Ethernet)
RX packets 1280614 bytes 140941048 (134.4 MiB)
RX errors 0 dropped 0 overruns 6 frame 0
TX packets 103678 bytes 21628629 (20.6 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device memory 0xc7100000-c711ffff
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 46 bytes 3148 (3.0 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 46 bytes 3148 (3.0 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
[host2 ~]$ route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 10.158.128.1 0.0.0.0 UG 0 0 0 enp3s0f1
10.158.128.0 0.0.0.0 255.255.240.0 U 0 0 0 enp3s0f1
169.254.0.0 0.0.0.0 255.255.0.0 U 1003 0 0 enp3s0f1
# service iptables status
Redirecting to /bin/systemctl status iptables.service
iptables.service - IPv4 firewall with iptables
Loaded: loaded (/usr/lib/systemd/system/iptables.service; enabled; vendor preset: disabled)
Active: inactive (dead)
ssh
asked Dec 4 at 15:11
rajen
1
add a comment |
up vote
-1
down vote
favorite
Hope ssh access host2 via host1, but ssh return "No route to host", but ping works and iptables return inactive.
[host1 ~] ping 10.158.131.165
PING 10.158.131.165 (10.158.131.165) 56(84) bytes of data.
64 bytes from 10.158.131.165: icmp_seq=1 ttl=58 time=1.69 ms
64 bytes from 10.158.131.165: icmp_seq=2 ttl=58 time=1.68 ms
^C
--- 10.158.131.165 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 1001ms
rtt min/avg/max/mdev = 1.684/1.687/1.690/0.003 ms
[host1 ~] telnet 10.158.131.165 22
Trying 10.158.131.165...
telnet: connect to address 10.158.131.165: No route to host
[host1 ~] ssh ssdrive@10.158.131.165
ssh: connect to host 10.158.131.165 port 22: No route to host
Host1:
[host1 ~] ifconfig
eno1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.166.62.130 netmask 255.255.240.0 broadcast 10.166.63.255
inet6 fe80::f64d:30ff:fe66:a895 prefixlen 64 scopeid 0x20<link>
ether f4:4d:30:66:a8:95 txqueuelen 1000 (Ethernet)
RX packets 3313964 bytes 529261130 (504.7 MiB)
RX errors 0 dropped 233 overruns 0 frame 0
TX packets 1258374 bytes 492612963 (469.7 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 16 memory 0xdf200000-df220000
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 8 bytes 528 (528.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 8 bytes 528 (528.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
[host1 ~] route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 10.166.56.1 0.0.0.0 UG 0 0 0 eno1
10.166.48.0 0.0.0.0 255.255.240.0 U 0 0 0 eno1
169.254.0.0 0.0.0.0 255.255.0.0 U 1002 0 0 eno1
# service iptables status
Redirecting to /bin/systemctl status iptables.service
iptables.service - IPv4 firewall with iptables
Loaded: loaded (/usr/lib/systemd/system/iptables.service; enabled; vendor preset: disabled)
Active: inactive (dead)
Host2:
[host2 ~]$ ifconfig
enp3s0f1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.158.131.165 netmask 255.255.240.0 broadcast 10.158.143.255
inet6 fe80::ec4:7aff:fe22:badf prefixlen 64 scopeid 0x20<link>
ether 0c:c4:7a:22:ba:df txqueuelen 1000 (Ethernet)
RX packets 1280614 bytes 140941048 (134.4 MiB)
RX errors 0 dropped 0 overruns 6 frame 0
TX packets 103678 bytes 21628629 (20.6 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device memory 0xc7100000-c711ffff
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 46 bytes 3148 (3.0 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 46 bytes 3148 (3.0 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
[host2 ~]$ route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 10.158.128.1 0.0.0.0 UG 0 0 0 enp3s0f1
10.158.128.0 0.0.0.0 255.255.240.0 U 0 0 0 enp3s0f1
169.254.0.0 0.0.0.0 255.255.0.0 U 1003 0 0 enp3s0f1
# service iptables status
Redirecting to /bin/systemctl status iptables.service
iptables.service - IPv4 firewall with iptables
Loaded: loaded (/usr/lib/systemd/system/iptables.service; enabled; vendor preset: disabled)
Active: inactive (dead)
ssh
asked Dec 4 at 15:11
rajen
1
Why is your routing table showing a normal (10.x.x.x) and APIPA (169.243.x.x) routing. How do you set the hosts' IP address? DHCP or static?
– Dirk
Dec 4 at 15:22
Can you runssh -vvv ssdrive@10.158.131.165and add the output to your question?
– Peschke
Dec 4 at 15:23
@Dirk ip is got by DHCP and I don’t know why a APIPA because not familiar with network
– rajen
Dec 4 at 15:28
@Peschke[host1 ~]$ ssh -vvv ssdrive@10.158.131.165 OpenSSH_6.6.1, OpenSSL 1.0.1e-fips 11 Feb 2013 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 56: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 10.158.131.165 [10.158.131.165] port 22. debug1: connect to address 10.158.131.165 port 22: No route to host ssh: connect to host 10.158.131.165 port 22: No route to host
– rajen
Dec 5 at 2:29
add a comment |
up vote
-1
down vote
favorite
up vote
-1
down vote
favorite
Hope ssh access host2 via host1, but ssh return "No route to host", but ping works and iptables return inactive.
[host1 ~] ping 10.158.131.165
PING 10.158.131.165 (10.158.131.165) 56(84) bytes of data.
64 bytes from 10.158.131.165: icmp_seq=1 ttl=58 time=1.69 ms
64 bytes from 10.158.131.165: icmp_seq=2 ttl=58 time=1.68 ms
^C
--- 10.158.131.165 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 1001ms
rtt min/avg/max/mdev = 1.684/1.687/1.690/0.003 ms
[host1 ~] telnet 10.158.131.165 22
Trying 10.158.131.165...
telnet: connect to address 10.158.131.165: No route to host
[host1 ~] ssh ssdrive@10.158.131.165
ssh: connect to host 10.158.131.165 port 22: No route to host
Host1:
[host1 ~] ifconfig
eno1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.166.62.130 netmask 255.255.240.0 broadcast 10.166.63.255
inet6 fe80::f64d:30ff:fe66:a895 prefixlen 64 scopeid 0x20<link>
ether f4:4d:30:66:a8:95 txqueuelen 1000 (Ethernet)
RX packets 3313964 bytes 529261130 (504.7 MiB)
RX errors 0 dropped 233 overruns 0 frame 0
TX packets 1258374 bytes 492612963 (469.7 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 16 memory 0xdf200000-df220000
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 8 bytes 528 (528.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 8 bytes 528 (528.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
[host1 ~] route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 10.166.56.1 0.0.0.0 UG 0 0 0 eno1
10.166.48.0 0.0.0.0 255.255.240.0 U 0 0 0 eno1
169.254.0.0 0.0.0.0 255.255.0.0 U 1002 0 0 eno1
# service iptables status
Redirecting to /bin/systemctl status iptables.service
iptables.service - IPv4 firewall with iptables
Loaded: loaded (/usr/lib/systemd/system/iptables.service; enabled; vendor preset: disabled)
Active: inactive (dead)
Host2:
[host2 ~]$ ifconfig
enp3s0f1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.158.131.165 netmask 255.255.240.0 broadcast 10.158.143.255
inet6 fe80::ec4:7aff:fe22:badf prefixlen 64 scopeid 0x20<link>
ether 0c:c4:7a:22:ba:df txqueuelen 1000 (Ethernet)
RX packets 1280614 bytes 140941048 (134.4 MiB)
RX errors 0 dropped 0 overruns 6 frame 0
TX packets 103678 bytes 21628629 (20.6 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device memory 0xc7100000-c711ffff
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 46 bytes 3148 (3.0 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 46 bytes 3148 (3.0 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
[host2 ~]$ route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 10.158.128.1 0.0.0.0 UG 0 0 0 enp3s0f1
10.158.128.0 0.0.0.0 255.255.240.0 U 0 0 0 enp3s0f1
169.254.0.0 0.0.0.0 255.255.0.0 U 1003 0 0 enp3s0f1
# service iptables status
Redirecting to /bin/systemctl status iptables.service
iptables.service - IPv4 firewall with iptables
Loaded: loaded (/usr/lib/systemd/system/iptables.service; enabled; vendor preset: disabled)
Active: inactive (dead)
ssh
asked Dec 4 at 15:11
rajen
1
Hope ssh access host2 via host1, but ssh return "No route to host", but ping works and iptables return inactive.
[host1 ~] ping 10.158.131.165
PING 10.158.131.165 (10.158.131.165) 56(84) bytes of data.
64 bytes from 10.158.131.165: icmp_seq=1 ttl=58 time=1.69 ms
64 bytes from 10.158.131.165: icmp_seq=2 ttl=58 time=1.68 ms
^C
--- 10.158.131.165 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 1001ms
rtt min/avg/max/mdev = 1.684/1.687/1.690/0.003 ms
[host1 ~] telnet 10.158.131.165 22
Trying 10.158.131.165...
telnet: connect to address 10.158.131.165: No route to host
[host1 ~] ssh ssdrive@10.158.131.165
ssh: connect to host 10.158.131.165 port 22: No route to host
Host1:
[host1 ~] ifconfig
eno1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.166.62.130 netmask 255.255.240.0 broadcast 10.166.63.255
inet6 fe80::f64d:30ff:fe66:a895 prefixlen 64 scopeid 0x20<link>
ether f4:4d:30:66:a8:95 txqueuelen 1000 (Ethernet)
RX packets 3313964 bytes 529261130 (504.7 MiB)
RX errors 0 dropped 233 overruns 0 frame 0
TX packets 1258374 bytes 492612963 (469.7 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 16 memory 0xdf200000-df220000
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 8 bytes 528 (528.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 8 bytes 528 (528.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
[host1 ~] route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 10.166.56.1 0.0.0.0 UG 0 0 0 eno1
10.166.48.0 0.0.0.0 255.255.240.0 U 0 0 0 eno1
169.254.0.0 0.0.0.0 255.255.0.0 U 1002 0 0 eno1
# service iptables status
Redirecting to /bin/systemctl status iptables.service
iptables.service - IPv4 firewall with iptables
Loaded: loaded (/usr/lib/systemd/system/iptables.service; enabled; vendor preset: disabled)
Active: inactive (dead)
Host2:
[host2 ~]$ ifconfig
enp3s0f1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.158.131.165 netmask 255.255.240.0 broadcast 10.158.143.255
inet6 fe80::ec4:7aff:fe22:badf prefixlen 64 scopeid 0x20<link>
ether 0c:c4:7a:22:ba:df txqueuelen 1000 (Ethernet)
RX packets 1280614 bytes 140941048 (134.4 MiB)
RX errors 0 dropped 0 overruns 6 frame 0
TX packets 103678 bytes 21628629 (20.6 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device memory 0xc7100000-c711ffff
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 46 bytes 3148 (3.0 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 46 bytes 3148 (3.0 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
[host2 ~]$ route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 10.158.128.1 0.0.0.0 UG 0 0 0 enp3s0f1
10.158.128.0 0.0.0.0 255.255.240.0 U 0 0 0 enp3s0f1
169.254.0.0 0.0.0.0 255.255.0.0 U 1003 0 0 enp3s0f1
# service iptables status
Redirecting to /bin/systemctl status iptables.service
iptables.service - IPv4 firewall with iptables
Loaded: loaded (/usr/lib/systemd/system/iptables.service; enabled; vendor preset: disabled)
Active: inactive (dead)
ssh
ssh
asked Dec 4 at 15:11
rajen
1
asked Dec 4 at 15:11
rajen
1
asked Dec 4 at 15:11
rajen
1
asked Dec 4 at 15:11
rajen
1
asked Dec 4 at 15:11
rajen
1
1
Why is your routing table showing a normal (10.x.x.x) and APIPA (169.243.x.x) routing. How do you set the hosts' IP address? DHCP or static?
– Dirk
Dec 4 at 15:22
Can you runssh -vvv ssdrive@10.158.131.165and add the output to your question?
– Peschke
Dec 4 at 15:23
@Dirk ip is got by DHCP and I don’t know why a APIPA because not familiar with network
– rajen
Dec 4 at 15:28
@Peschke[host1 ~]$ ssh -vvv ssdrive@10.158.131.165 OpenSSH_6.6.1, OpenSSL 1.0.1e-fips 11 Feb 2013 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 56: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 10.158.131.165 [10.158.131.165] port 22. debug1: connect to address 10.158.131.165 port 22: No route to host ssh: connect to host 10.158.131.165 port 22: No route to host
– rajen
Dec 5 at 2:29
add a comment |
Why is your routing table showing a normal (10.x.x.x) and APIPA (169.243.x.x) routing. How do you set the hosts' IP address? DHCP or static?
– Dirk
Dec 4 at 15:22
Can you runssh -vvv ssdrive@10.158.131.165and add the output to your question?
– Peschke
Dec 4 at 15:23
@Dirk ip is got by DHCP and I don’t know why a APIPA because not familiar with network
– rajen
Dec 4 at 15:28
@Peschke[host1 ~]$ ssh -vvv ssdrive@10.158.131.165 OpenSSH_6.6.1, OpenSSL 1.0.1e-fips 11 Feb 2013 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 56: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 10.158.131.165 [10.158.131.165] port 22. debug1: connect to address 10.158.131.165 port 22: No route to host ssh: connect to host 10.158.131.165 port 22: No route to host
– rajen
Dec 5 at 2:29
Why is your routing table showing a normal (10.x.x.x) and APIPA (169.243.x.x) routing. How do you set the hosts' IP address? DHCP or static?
– Dirk
Dec 4 at 15:22
Why is your routing table showing a normal (10.x.x.x) and APIPA (169.243.x.x) routing. How do you set the hosts' IP address? DHCP or static?
– Dirk
Dec 4 at 15:22
Can you run
ssh -vvv ssdrive@10.158.131.165 and add the output to your question?– Peschke
Dec 4 at 15:23
Can you run
ssh -vvv ssdrive@10.158.131.165 and add the output to your question?– Peschke
Dec 4 at 15:23
@Dirk ip is got by DHCP and I don’t know why a APIPA because not familiar with network
– rajen
Dec 4 at 15:28
@Dirk ip is got by DHCP and I don’t know why a APIPA because not familiar with network
– rajen
Dec 4 at 15:28
@Peschke
[host1 ~]$ ssh -vvv ssdrive@10.158.131.165 OpenSSH_6.6.1, OpenSSL 1.0.1e-fips 11 Feb 2013 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 56: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 10.158.131.165 [10.158.131.165] port 22. debug1: connect to address 10.158.131.165 port 22: No route to host ssh: connect to host 10.158.131.165 port 22: No route to host– rajen
Dec 5 at 2:29
@Peschke
[host1 ~]$ ssh -vvv ssdrive@10.158.131.165 OpenSSH_6.6.1, OpenSSL 1.0.1e-fips 11 Feb 2013 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 56: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 10.158.131.165 [10.158.131.165] port 22. debug1: connect to address 10.158.131.165 port 22: No route to host ssh: connect to host 10.158.131.165 port 22: No route to host– rajen
Dec 5 at 2:29
add a comment |
active
oldest
votes
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "106"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
draft saved
draft discarded
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2funix.stackexchange.com%2fquestions%2f485912%2fssh-for-no-route-to-host-but-ping-works%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
active
oldest
votes
active
oldest
votes
active
oldest
votes
active
oldest
votes
draft saved
draft discarded
Thanks for contributing an answer to Unix & Linux Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
draft saved
draft discarded
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2funix.stackexchange.com%2fquestions%2f485912%2fssh-for-no-route-to-host-but-ping-works%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Why is your routing table showing a normal (10.x.x.x) and APIPA (169.243.x.x) routing. How do you set the hosts' IP address? DHCP or static?
– Dirk
Dec 4 at 15:22
Can you run
ssh -vvv ssdrive@10.158.131.165and add the output to your question?– Peschke
Dec 4 at 15:23
@Dirk ip is got by DHCP and I don’t know why a APIPA because not familiar with network
– rajen
Dec 4 at 15:28
@Peschke
[host1 ~]$ ssh -vvv ssdrive@10.158.131.165 OpenSSH_6.6.1, OpenSSL 1.0.1e-fips 11 Feb 2013 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 56: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 10.158.131.165 [10.158.131.165] port 22. debug1: connect to address 10.158.131.165 port 22: No route to host ssh: connect to host 10.158.131.165 port 22: No route to host– rajen
Dec 5 at 2:29